Looking for complete front end for F2 and up for reasonable price.
I might be able to use any other sport/street Honda front end with dual brakes also.
Need this for a supermono project
Let me know if you have something I might use.
Thx Martin
Looking for complete front end for F2 and up for reasonable price.
I might be able to use any other sport/street Honda front end with dual brakes also.
Need this for a supermono project
Let me know if you have something I might use.
Thx Martin
Martin J. #73 - Motoforza Racing Team
Motoforza bodywork www.motoforzafairings.com
Cell: 303-518-5650
http://i278.photobucket.com/albums/k...gpic3918_6.jpg
Martin,
How about an SV front end?
S
MRA Expert #69
Sponsored by: Chicane Instruction
STM Suspension, Speedin' Motorsports
Northern Colorado Euro Motorcycles
Boulder Motorsports, Sol Performance Pirelli
Angry Marmot Motorsports
Sarah, Aaron and David
Only one side brake. I would like to have 2. Need to fit Hawk 650 frame.
But if I do not find any then I will have to look at it if that will fit.
Martin J. #73 - Motoforza Racing Team
Motoforza bodywork www.motoforzafairings.com
Cell: 303-518-5650
http://i278.photobucket.com/albums/k...gpic3918_6.jpg
Sv has 2 front brakes
and the same fork tube diameter as the Hawk (41mm)
Should be able to slide these tubes right into your triples and go!
I have: Forks, wheel, brake rotors, calipers, master cylinder, clip on's, triples (if you need them) etc.
MRA Expert #69
Sponsored by: Chicane Instruction
STM Suspension, Speedin' Motorsports
Northern Colorado Euro Motorcycles
Boulder Motorsports, Sol Performance Pirelli
Angry Marmot Motorsports
Sarah, Aaron and David
I would suggest getting an F3 front end instead. Same fork tube diameter, but fully adjustable cartridge style internals and bigger brakes with same fitment options. Another front end that fits is the early 90's GSX-R 750 inverted forks. What's the motor Martin?
I'm planning to use XR650R motor but did not find one yet so that is still to be decided
Scot, if that's the case, I would like to look at it. How much?
I think whatever will fit I will use
Martin J. #73 - Motoforza Racing Team
Motoforza bodywork www.motoforzafairings.com
Cell: 303-518-5650
http://i278.photobucket.com/albums/k...gpic3918_6.jpg
sent you a PM martin
MRA Expert #69
Sponsored by: Chicane Instruction
STM Suspension, Speedin' Motorsports
Northern Colorado Euro Motorcycles
Boulder Motorsports, Sol Performance Pirelli
Angry Marmot Motorsports
Sarah, Aaron and David
I have a 95 900RR front end.
Going to try Scots SV front end. If that dos not work I'll get back to you for that 900rr.
Martin J. #73 - Motoforza Racing Team
Motoforza bodywork www.motoforzafairings.com
Cell: 303-518-5650
http://i278.photobucket.com/albums/k...gpic3918_6.jpg
If you do grab an entire front end from the 900RR, it's a 16 inch wheel and the tire is a 130/70. I believe the common conversion there is an F3 front wheel.
Thx for the input Chris
I think that's out of question then as I do not want to use 16 inch wheel.
I hope that the SV will fit
Martin J. #73 - Motoforza Racing Team
Motoforza bodywork www.motoforzafairings.com
Cell: 303-518-5650
http://i278.photobucket.com/albums/k...gpic3918_6.jpg
i have a complete 01 vfr800 front end with leaking forks, it's in new mexico though
Going to try the SV front first then will see after that.
Martin J. #73 - Motoforza Racing Team
Motoforza bodywork www.motoforzafairings.com
Cell: 303-518-5650
http://i278.photobucket.com/albums/k...gpic3918_6.jpg
All you do with the 900rr front end is put on the 17" wheel from a F3 and there you go. On a side note the 900 front is waaaaaaay better than a SVs.Originally Posted by Mforza
Thx Bart
I might give it a try.
Martin J. #73 - Motoforza Racing Team
Motoforza bodywork www.motoforzafairings.com
Cell: 303-518-5650
http://i278.photobucket.com/albums/k...gpic3918_6.jpg
PM replied to. 8)Originally Posted by Mforza