Page 2 of 2 FirstFirst 12
Results 26 to 35 of 35

Thread: It costs how much to race????

  1. #26
    Senior Member Expert
    Join Date
    Mar 2005
    Location
    Denver
    Posts
    4,077
    Quote Originally Posted by kfm61
    Hey Dave, I followed you into turn 1 in the colorado class. I'll tell you what, I almost forgot that 400 pounds of Thruxton wasn't going to turn like your Motard!

    Dang, it's rough on the outside of turn 1 ! Bike jumps, parts hit, and I start mutterng single word sentances like "S*&#, F@^*%, over and over really fast!

    Fun time though!
    Those Thruxtons sound so sweet singing down the front straight there at Pueblo.

    The motard turns great, that is for sure! It definitely has some room for improvement though as I run out of gear about 100 feet before start/finish line and the front chatters so much it blurs my vision! :shock:

    Still, it was a lot of fun helping fill out the class and being back in the Colorado Class. I have not raced in that class since like 2000!



    (My KX500 was like twice as fast as this 450! And Mark Erickson and Chuck S have wicked fast roadracer 500s)
    dave@MotoSix DOT com | MRA #31, WERA #311

  2. #27
    Senior Member Expert
    Join Date
    Nov 2007
    Location
    Longmont C.O.
    Posts
    853
    Quote Originally Posted by elvis8310@hotmail.com
    that was cool to watch you zip around the track on that motard : )
    how is taht stock suspension in turn 1? : P
    So as seeing I have never been on one of the Colorado tracks, is there something special I should know about turn one?[/quote]

    Turn one is fast and bumpy : P

  3. #28
    Senior Member Amateur
    Join Date
    Jun 2008
    Location
    Fountain
    Posts
    156
    Quote Originally Posted by cromer611
    Quote Originally Posted by elvis8310@hotmail.com
    that was cool to watch you zip around the track on that motard : )
    how is taht stock suspension in turn 1? : P
    So as seeing I have never been on one of the Colorado tracks, is there something special I should know about turn one?
    Turn one is fast and bumpy : P[/quote]

    Ok, so as long as I have built forks and a new rear shock all is good then(25 mm Ohlins cartridge inserts and elk rear shock already on bike).

  4. #29
    Senior Member Expert
    Join Date
    May 2005
    Posts
    509
    Quote Originally Posted by MotoSix
    OK - So there can be some cheap racing.

    I raced on $9 worth of pump gas, free take offs, and travel $ this weekend. 4 races and an endurance.


    (on my CRF450 motard ) :shock:

    Cheap thrills. More cheap than thrilling, but a good time none the less and something to consider for those on a serious budget. Stock motor, stock suspension slightly lowered, 17" wheels, go race. Not fast, but it is racing none the less!
    how did you gear it compared to imi?
    Benny Tozzi #78
    Tri City Cycle
    Check out Dave@SingleTrackMind for your suspension needs!
    www.fixmybike.com

    www.getwellclarkie.com

  5. #30
    Senior Member Expert
    Join Date
    Mar 2005
    Location
    Denver
    Posts
    4,077
    Quote Originally Posted by motobum
    Quote Originally Posted by MotoSix
    OK - So there can be some cheap racing.

    I raced on $9 worth of pump gas, free take offs, and travel $ this weekend. 4 races and an endurance.


    (on my CRF450 motard ) :shock:

    Cheap thrills. More cheap than thrilling, but a good time none the less and something to consider for those on a serious budget. Stock motor, stock suspension slightly lowered, 17" wheels, go race. Not fast, but it is racing none the less!
    how did you gear it compared to imi?
    I put the smallest rear sprocket I could buy on it, which is 5 less teeth on the rear than IMI.

    I am probably 6-8 teeth off from where it needs to be with the stock motor.

    The 450X has a wide ration transmission, and Jeff Winter on his CRF450X/RS125 is 11(ish) teeth taller than I am and his works well at Pueblo.
    dave@MotoSix DOT com | MRA #31, WERA #311

  6. #31
    Senior Member Expert
    Join Date
    May 2005
    Posts
    509
    Quote Originally Posted by MotoSix
    Quote Originally Posted by motobum
    Quote Originally Posted by MotoSix
    OK - So there can be some cheap racing.

    I raced on $9 worth of pump gas, free take offs, and travel $ this weekend. 4 races and an endurance.


    (on my CRF450 motard ) :shock:

    Cheap thrills. More cheap than thrilling, but a good time none the less and something to consider for those on a serious budget. Stock motor, stock suspension slightly lowered, 17" wheels, go race. Not fast, but it is racing none the less!
    how did you gear it compared to imi?
    I put the smallest rear sprocket I could buy on it, which is 5 less teeth on the rear than IMI.

    I am probably 6-8 teeth off from where it needs to be with the stock motor.

    The 450X has a wide ration transmission, and Jeff Winter on his CRF450X/RS125 is 11(ish) teeth taller than I am and his works well at Pueblo.
    holy crap do you have to be on the rev limiter to get it off the line?

    i bet ppir will be fun on a 450
    Benny Tozzi #78
    Tri City Cycle
    Check out Dave@SingleTrackMind for your suspension needs!
    www.fixmybike.com

    www.getwellclarkie.com

  7. #32
    Senior Member Expert
    Join Date
    Mar 2005
    Location
    Denver
    Posts
    4,077
    Quote Originally Posted by motobum
    holy crap do you have to be on the rev limiter to get it off the line?

    i bet ppir will be fun on a 450
    Nah - it out-launches anything else on the grid pretty easily still.
    dave@MotoSix DOT com | MRA #31, WERA #311

  8. #33
    Senior Member Expert
    Join Date
    May 2005
    Posts
    509
    Quote Originally Posted by MotoSix
    Quote Originally Posted by motobum
    holy crap do you have to be on the rev limiter to get it off the line?

    i bet ppir will be fun on a 450
    Nah - it out-launches anything else on the grid pretty easily still.
    lol thats awesome
    Benny Tozzi #78
    Tri City Cycle
    Check out Dave@SingleTrackMind for your suspension needs!
    www.fixmybike.com

    www.getwellclarkie.com

  9. #34
    Senior Member Expert
    Join Date
    Mar 2005
    Location
    Denver
    Posts
    4,077
    Quote Originally Posted by motobum
    Quote Originally Posted by MotoSix
    Quote Originally Posted by motobum
    holy crap do you have to be on the rev limiter to get it off the line?

    i bet ppir will be fun on a 450
    Nah - it out-launches anything else on the grid pretty easily still.
    lol thats awesome
    I took my time getting off the line because a few thought I jumped the first few starts since I shot through like 5 rows in the first 25 feet.

    The only problem was that by the time I hit the timing light area, I was already in 5th gear at close to max RPM! :shock:
    dave@MotoSix DOT com | MRA #31, WERA #311

  10. #35
    Senior Member Expert
    Join Date
    May 2005
    Posts
    509
    Quote Originally Posted by MotoSix
    Quote Originally Posted by motobum
    Quote Originally Posted by MotoSix
    Quote Originally Posted by motobum
    holy crap do you have to be on the rev limiter to get it off the line?

    i bet ppir will be fun on a 450
    Nah - it out-launches anything else on the grid pretty easily still.
    lol thats awesome
    I took my time getting off the line because a few thought I jumped the first few starts since I shot through like 5 rows in the first 25 feet.

    The only problem was that by the time I hit the timing light area, I was already in 5th gear at close to max RPM! :shock:
    hahahaha man i wish i wasnt so broke and could join you... are you going to be at imi for epics race this weekend?
    Benny Tozzi #78
    Tri City Cycle
    Check out Dave@SingleTrackMind for your suspension needs!
    www.fixmybike.com

    www.getwellclarkie.com

Page 2 of 2 FirstFirst 12

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •